Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Compression on street tunnel ram
User Name
Password
lost password?   |   register now

Thread: Compression on street tunnel ram Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-25-2007 01:27 AM
383 Thanks for all your input on my questions.
I think 11.5 is what i will use.
Thanks for a great forum.
11-23-2007 08:58 PM
chrismac If you are building a track ride you need a real bottom end to handle 7500 rpm all the time. Get loose clearances on the mains and rods, Tight clearances on the pistons, lots of camshaft and heads to match. When all said and done you will have a radical 383 12:1 compression or higher and 2gs in the heads and valvetrain just to make the motor last for the long run. 1.5 hp per c.i. is great but its gonna take more than just an intake.
11-23-2007 08:41 PM
1930u
Quote:
Originally Posted by 383
Hi,can anyone tell me the highest compression for 102 octane fuel. Could 12.5 with a big cam do it or not?
The edelbrock street tunnel ram,does it need a high compression?
The isky Z-60 grind cam is old school but it works great with a tunnel ram and 10.5 compression. I used it in a .060 over 327 with 4-speed and a 4:56 gear.

Here's the cam specs. High performance. Street/strip. Lopey idle. 3200 Stall. 4:56-4:88 axle ratio. Up to 800 CFM Carb. 10.5-11:1 compr. RPM-Range (3500-7500) Valve Lift (.548 .548) Valve Lash hot (.016 .016) ADV Duration (292 292) .050 Duration (259 259) LC 108...The motor flat out beat the ground (sounded to nice) and it wasn't to bad driveability wise either. Probably wouldn't be as much fun with an automatic.
11-23-2007 07:37 AM
woodz428
Quote:
Originally Posted by 383
On the street ram ,if a cam gets used that makes peak power above 7000rpm,
would it still make good power there? Edelbrock said its for under 7500rpm motors.
I would like to make 1.4-1.5hp per cubic inch.(383)
Can it be done with this setup? I need to choose the rotating assemblies compression and cam.
It appears to me you are building an engine from the manifold down. That is kind of backwards to the way that I think it should be done. Depending on those components that you have yet to choose, it shouldn't be hard to get the 1.5hp per cube....with just a 4 barrel.
11-23-2007 06:55 AM
383 On the street ram ,if a cam gets used that makes peak power above 7000rpm,
would it still make good power there? Edelbrock said its for under 7500rpm motors.
I would like to make 1.4-1.5hp per cubic inch.(383)
Can it be done with this setup? I need to choose the rotating assemblies compression and cam.
11-22-2007 11:40 PM
383 So the street ram don't need the compression the high rpm rams do.
You reckon 600cfm carbs would be a overkill. At just over 7000rpm
would it still be?
The car is a strip car and would not see road time,if it does ones a month.
11-22-2007 06:45 PM
chrismac F-Bird is right. A huge cam with a lot of compression isn't really any fun just to run pump gas. I just went through the same crap with a small block 350 bored .030 and domes. I ran a huge cam and it was lazy until 4,000 rpm. I just stepped down from a camshaft that is 310/320 In/ex. duration advertised and 262/270 in./ex. @.050 To a comp cams 294s grind number 12-224-4 in hopes for more bottom end and streetability. There isn't a need of high compression for a tunnel ram because the create a lot of velocity going down the intake runners which helps the engine rev quickly.
11-22-2007 01:02 PM
383
Compression on street tunnel ram

Hi,can anyone tell me the highest compression for 102 octane fuel. Could 12.5 with a big cam do it or not?
The edelbrock street tunnel ram,does it need a high compression?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.