Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Is all of this be Good for the street ?
User Name
Password
lost password?   |   register now

Thread: Is all of this be Good for the street ? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-14-2008 09:36 PM
Stroke Mostly that a DP is not primarily used, nor was it designed for 'street driven' vehicles. Sure, guys run 'em and like 'em. Do the guys who use them know if they're the best carb for their app? I doubt it. Toss on an old 3310 VS and see where you're at. The VS carb is only going to deliver what the motor needs, no more, no less - when properly tuned. The DP delivers an overly abundant supply of fuel for most 'street driven' applications and is not necessary but to say you run a DP. JMO
01-14-2008 09:12 PM
Mustangsaly those are not vortec heads.

what wrong with the 700 cfm with mechanical secondaries


my build is a 350 4 bolt main vortec block with vortec heads and roller cam & GM LT4 "HOT" cam kit. duration @ .050 is 218*/228* .525" lift with 1.6 rockers, LSA is 112*. and a 750cfm mechanical secondaries. but I have been offered a 650 & 700 double pumper with mechanical secondaries I'm running a 4 speed & 411 gears.
01-14-2008 08:40 PM
Stroke It's too much for 400 HP. The Vac Sec would be waaaay better. You'll be fouling plugs and running rich even if you jet it down.
01-14-2008 07:49 PM
chevy350_Camd
okay thanks

So wats so wrong about my carb ?
01-14-2008 07:44 PM
Double_v23 Yeah that is exactly what it does but by hot they may have meant engine temperature, it is not alot earlier only 4 degrees out of 360 (or 720?) it creates higher engine temperatures by "leaning" out the engine.
01-14-2008 07:21 PM
chevy350_Camd
any info helps

Thanks someone told me it would run alot hot( as in fast off the line) and kick the cam in alot earlier
01-14-2008 07:19 PM
Double_v23 Probably not. Just kidding, you don't need to have a double roller to advance the timing they sell crankshaft keys and if you have a degree wheel you can do it differently as well.

You might see a gain of 4 ft/lbs of torque and 5 hp and you may lose .5 Hg of idle vacuum.

Does that help?
01-14-2008 07:16 PM
chevy350_Camd
UMMM ok ....

So ur telling me if i advanced the timing on the roller to the triangle it wouldnt do anything lol
01-14-2008 07:14 PM
Double_v23 If you have asked this alot and you want more responses try bringing your previous posts back to the top of the list by actually responding to the answers people give you.

It will give people a history of what you already know,

The setup is fine except for the mechanical secondaries. And why do keep listing the Double roller? It has no bearing on performance or driveability whatsoever.

It is pretty annoying to open a new thread only to see the same question a half dozen times in 1 week!!
01-14-2008 06:50 PM
chevy350_Camd
Is all of this be Good for the street ?

Okay, From what I have been told from this awesome site, these parts would be fairly close to 400 hp and would be decent for street and higher rpm racing.

700 Cfm Holley Double Pumper Mech Sec.
Edelbrock Rpm Manifold 1500 - 6500
Vortec Heads Casting Number 14102193 1.94 and 1.5 valves
Summit Cam lift 466 and 488 with 224 and 234 dur,
Afterburner Headers
And a Comp Cams Double Roller

Can any of you tell me the specs on those heads ?
Also, What would happen if I advanced the timing on the crank with the roller ? Would the motor be different or the same ?

I know Ive asked this alot and Im sorry about that but im double checking before I pour money Into nothing

Thank you

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:00 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.