Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Rust inbetween Double Seem Questions Advice on ATTACK Plan
User Name
lost password?   |   register now

Thread: Rust inbetween Double Seem Questions Advice on ATTACK Plan Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-21-2008 11:20 PM
fcastro Hey baddbob its actually a 92 camaro Today I poured some water into the water channel and nothing came through so I think its getting caught up in the back of the wheel well. I am sure the seam sealer has failed.

Hmmm so epoxy primer and then some urethane seam sealer if I am able to open up the seams. I will give opening the seam a try. It looks really challenging since there are 3 walls to try and open up but if thats possible it makes sense.

Also forgot to memtoin that the rust has some permatex rust blocker on it (put it on there temporarily) and that is why its black.
01-21-2008 07:57 PM
baddbob The rust looks like a result of moisture crawling into the seam from the bottom. Sometimes dust, etc.. will collect in the seams and actually draw moisture in and hold it there. Is this a european car? it doesn't look familiar to me. Sometimes you can work a stiff putty knife or scraper between the spotwelds and spread the seam open enough to clean it out well with a spot blaster. Us a hammer and tap that putty knife in easily and carefully and the seam will stretch open between the welds. After cleaning just brush some epoxy primer in there, then apply some urethane seam sealer and then hammer and dolly them closed allowing the extra sealer to squish out-I've done this quite a few times when access allowed.
01-20-2008 10:38 PM
Rambo_The_Dog Sounds like you already have a good idea the only way to get rid of it is to cut it out and replace.

That being said your plan of attack doesn't sound too bad.

I've learned that in certain circumstances you can only do the best that you can do given acsess, time, budget, skills and tools available.

Then, someday down the road when or if it gets worse in the time you own the car - you can always cut and repair then.
01-20-2008 09:57 PM
Rust inbetween Double Seem Questions Advice on ATTACK Plan

Hi all,

I have discovered some rust in my car but I am having a tough time deciding how to fix it . In the picture below I am going to cut out the inner passenger floor board hole and put new sheet metal (shown in green) in. Now the problem is I cannot get behind the curved wheel well where I believe the seem sealer has failed (water is indicated by the green and blue puddles). I am still unsure where the leak is coming from but its 1 of those 2 spots.

There is rust on the inside triple sheet metal welded walls as you can see from the photo. So I was thinking to use some sort of rust converter (such as picklex 20 or eastwoods rust converter other suggestions?) and pouring it into the hole once I find it. After that wheel off as mush rust as possible and then apply some sort of encapsulator such as rust bullet. Then apply seam sealer on top of the rust bullet. On the interior I would wheel off as must rust as possible and apply rust bullet on top of that. My thinking is once the rust bullet and the seam sealer are down no more water will penetrate and hence the rust will not be able to grow anymore.

What are peoples thoughts on this attack plan?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:02 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.