Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> best way to run water/methanol injection with dual carbs?
User Name
Password
lost password?   |   register now

Thread: best way to run water/methanol injection with dual carbs? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-08-2008 09:08 PM
junior stocker
h 2 o injection

I too have wondered that, but moreso about making my own kit. Also, you hear of folks pouring water down the carb throat at high speed to clean the carbon out of the motor. So, I took a plastic irrigation solution bottle (hospital item, 2 liters), and filled it with water and a little rubbing alcohol, put a small diameter tube into the container and the other end onto the vacuum advance nipple of the carb. This was on full centrifugal advance ditributor setup, and drove around that way. Did'nt seem to hurt anything, can't say it helped, but I reasonned that the engine would pull more vacuum under load, and therefore more water ,to stave off detonation. Could one "tune" it with some sort of jetting, and would that work?
02-08-2008 04:13 PM
darkostoj
Quote:
Originally Posted by Bat 21
Why would you want to have water injected?
i'm at 9:1 static compression and want to run as much boost as possible with my timing locked out on pump gas.
02-08-2008 01:42 PM
Bat 21 Why would you want to have water injected?
02-08-2008 10:28 AM
Chevrolet4x4s What about using some nitrous plates?

Shane
02-08-2008 08:48 AM
hyarbour
re:best way to run water/methanol injection with dual carbs?

You can contact the companies that make those system's (like Snow) to see if they have any suggestions. I'll be putting water injection in my truck (non-blower/turbo), but as far as I know it needs to be injected under the throttle plates.
02-07-2008 02:48 PM
darkostoj
best way to run water/methanol injection with dual carbs?

I got a 671 blower and I was wondering what would be the best way to run water injection on these? The only way I can think of is running a spacer thats been tapped for the nozzles under the carbs. I would like to avoid using spacers, is there an alternative that I haven't thought about?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:48 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.