|06-13-2008 10:21 PM|
|PUREAUDIO||wow that came out real nice|
|06-02-2008 03:24 PM|
|NEW INTERIORS||That's some great looking seats man!!!! I would love to be able to do that.|
|06-02-2008 02:03 PM|
|DanTwoLakes||That seems incredibly unsafe to me. I was expecting them to have some kind of brackets to hold the back and seat together, do they have that, are they assembled differently like with hinges of some kind, or don't they get assembled at all? Are the seat and back just two solid pieces of plywood? How are the bolsters made, are they just plywood also, or are they more substantial than that? It seems to me they would have to be stronger.|
|06-02-2008 01:13 PM|
I will be adding a seperate back piece to it, the whole seat is modular the bolsters come off so they can be upholstered partially then screwed back on to finish wrapping the upholstery around the outside edge.
Actually I upholstered the centers first then the bolsters attached. I used staples throughout the build, like i said they are all plywood and foam, so really no framework to speak of, which means they are not all that safe, compared to stock retrofitted seat.
|06-02-2008 01:05 PM|
|DanTwoLakes||That looks super, nice job. Do the bolster areas get done first and then the center sections like a boat's captain's chair? Is the outside of the seat back separate, or attached to the bolsters? How are they attached, staples, hog rings, listing wires? Do you have any pictures of the bare frames?|
|06-02-2008 12:36 PM|
I got it all figured out
Just finished this seat yesterday, wasn't as bad as I had suspected just took a liitle longer than most
|03-24-2008 09:19 PM|
Either way, with that tyoe of seat, you maintain shape with hog rings, listing wires and or glue. The hard part is shaping them consistently if you don't use a mold or shaping guide.
|03-19-2008 08:22 AM|
Usually seats like this do not have any wood to staple to like Chavers and Mangus like to do them. The frame is usually tube steel and the bottom is steel and usually a flexalator of some sort on the bottom. That is the reason why they are usually wire and hog rings.
|03-18-2008 07:47 PM|
|stitcher_guy||Custom made like that are usually glued on the facings, stapled on back, with a cover clipped in place. At least according to Sid Chavers, Ron Mangus and Don Taylor in their educational videos and books, and a conversation I had with Chavers. But I've not done one with wood on the backrest.|
|03-18-2008 08:29 AM|
How do they upholster this kind of seat?
The quick version!
The bottom bun is usually done as three separate pieces. Bolsters, and center pad. They are almost always held down between each other with a long wire and hog rings.
The seat back is a little different. The two side bolsters and the back cover are sewn together to form one piece. this is then wrapped around the back of the seat and held in a similar fashion as the bottom is. The center pad with the headrest area, are again a separate piece but done in a similar fashion as the bottom.
I have done several Ricaro and Flow-Fit seats that are built this way.
|03-18-2008 08:06 AM|
|DanTwoLakes||You'll have better luck just calling him on the phone.|
|03-17-2008 09:42 PM|
I'll try to call Shannon tomorrow or drop him an email. As I make some progression I will post some pics.
|03-17-2008 09:31 PM|
|03-17-2008 09:08 PM|
|NEW INTERIORS||You and me both would love to know how they make them seat's.|
|03-17-2008 06:57 PM|
how is a seat like this upholstered?
A customer of mine brought in a pair of custom built seats made up of plywood and foam. My question is how are these sewn and upholstered. Are the bolsters sewn to the insert and then upholstered or are the bolsters upholstered separately from the insert? How are they attached: staples, listings, glue, other? Just so everyone knows I borrowed these pics from Interiors by Shannon, hope he doesn't mind, they are close to what I need to build up.