|04-01-2008 06:55 PM|
The POR15 guy told me to use the black rust paint first and then top coat with the color. I brushed mine on within 24 hours so I wouldn't have to scuff the black.
Only issue I had was close to the center exhaust ports on the heads , the red discolored from the intense heat. 455 OLDS with siamesed exhaust ports in the center.
|04-01-2008 11:32 AM|
I plan to use their engine enamel. I would be very suprized and disappointed if POR-15 would promote a product for engines that did not stand up to their claims. Like I said, I have used their other products on the frame and body with unquestionable success. I'm expecting the same from this product. I did check out the local auto supply stores and they have Dupli-Color high performance engine enamel and primer for a lot less than the POR-15 products. I want a quality, reliable and problem free finish that will look good for years to come. That's why I thought POR-15 would be the best.
Bottom line, I'm going with the POR-15 engine enamel and I'm going to mask the parts and paint them before assembly.
Thanks again for all your advice and ideas. Sure helps to have a good staff of people to call on.
|03-27-2008 07:32 PM|
This is THE way to do it
|03-27-2008 10:48 AM|
|03-27-2008 06:49 AM|
It is their Engine Enamel product. I would be very surprised if POR-15 represented a product for engine use that had not been tested. I have used their products on other applications on the car that are working extremely well. Some of the product has been in use over 6 years and it still looks as good as the day it was first applied.
I was more interested in when the best time was to do the painting. I've decided to paint before assembly so the bolts and accessories stand out more.
One more question. Should the surfaces where bolts occur on the exterior be masked off so bolts mate metal to metal or is a layer of paint between the bolt and the part an acceptable alternative. I'm thinking the surfaces probably should be masked off to assure metal to metal contact.
|03-21-2008 01:58 PM|
You need to clarify. Are you wanting to use the black POR-15 rust paint? Or the POR-15 engine enamals they also sell?
I, like the other posters had the impression you were using the rust paint they are so well known for. If your talking about thier special engine enamal, I have no experiance with it, but I would retract my statement about it being the wrong application.
|03-21-2008 01:12 PM|
Have smelled more than my share of POR.
|03-21-2008 01:01 PM|
|03-21-2008 12:58 PM|
not a paid advertiser/endorser of any known product
Anyway, anybody that doesn't care for the POR stuff, all I can ask is WHY?
|03-21-2008 11:20 AM|
|jpd37||Thanks for the feedback. I know I can always count on my fellow car nuts to give me the straight scoop. I think I'll paint before assembly because I want the detail to show. I think I will go the bc/cc approach over an epoxy primer. I don't plan on tearing into this motor again for quite some time and I want it to look kick ___. Thanks!|
|03-21-2008 06:39 AM|
|Arrowhead||I vote against the POR-15 also. It's just not the right application. I've had good luck with can engine paint, but epoxy/bc/cc is the way to go. The clear coat makes it super easy to clean. Some engine degreaser and good hose down and the the grime rinses away.|
|03-20-2008 10:24 PM|
|03-20-2008 09:36 PM|
|baddbob||A high quality epoxy primer followed by automotive Single stage urethane gets my vote.|
|03-20-2008 03:44 PM|
I paint after assembly because I think its easier. Restoration freaks tend to paint before assembly because it is more authentic, but it requires more masking and attention to detail.
I agree with the others; unless you're doing a special POR15 engine paint, I wouldn't use it. Its great as a rock hard topcoat for rust, but you'll have to topcoat it and I don't think its best on hot engine parts. I have great luck with Eastwood rattle cans of engine paint, and actually the parts-store brand is just fine as well.
|03-20-2008 03:31 PM|
I would vote against POR-15. Once it sets, it turns to concrete and makes any mistakes a headache.
I always paint after assembly. Less masking.
|This thread has more than 15 replies. Click here to review the whole thread.|