|07-30-2014 07:09 AM|
|ap72||I always run the lash tighter than called for- it increases your actual seat duration slightly but it also quiets it up a lot. You can get cams ground with a "tight lash" opening ramp, needing as little as .010-.015" lash. The tighter it is the quieter it is- go too tight and you backfire or burn a valve seat.|
|07-30-2014 06:04 AM|
|MouseFink||Two cam lobes going flat.|
|07-29-2014 07:09 PM|
|07-29-2014 07:06 PM|
|07-29-2014 06:51 PM|
|Dajerseyrat||What would cause only 2 of the valve lash's to be extremely off within a few miles of driving? Bad Poly lock?|
|07-29-2014 11:45 AM|
|MouseFink||I had a 1965 Chevrolet 30-30 camshaft in my 1959 Chevy Impala with a 1965 327 engine and it was a daily driver. I installed a new over-the-counter 1965 327 CI short block in my Impala. When I installed the new engine, I initially set the valve lash at .030" intake and exhaust and checked the lash again about four months later and the lash was still .030". I checked the lash two years later just before I sold the car and the lash was still 030" . The engine had Joe Mondello prepared 461 heads, slightly used Crane valve springs set up with 100 lb. seat pressure at 1.700" and 290 lb. open pressure at .485" lift using 3/8" screwed-in rocker studs. I was also using stock rocker arms. The screw-in studs kept the lash at .030".|
|07-29-2014 10:42 AM|
|BuzzLOL||. Yeah, in an occasionally driven mild street car, lash may only need re-adjusting every 10 years or so...|
|07-29-2014 09:07 AM|
|07-28-2014 02:36 PM|
What cam is it? What rockers?
It is very hard to set the lash "HOT".
Thats why I do it and recomend the COLD
When you have a good, painless method,
You don't mind doing it and get a consistant
When you learn the sound of the motor when the lash
Is set right, you will know when it needs adjustment
By the sound.
|07-28-2014 02:24 PM|
The Scorpion roller rockers are much quieter than others I have heard.
Even with solid cams.
|07-28-2014 02:22 PM|
Needs *periodic* relashing.
Much like changing the oil or lubing the door locks and hinges.
Big difference between constant and periodic.
Are you constantly changing the oil?
|07-28-2014 02:16 PM|
|MouseFink||Roller rocker arms are more noisy by design than stock GM type steel ball fulcrum rockers. I chased valve train noise for a year before I was told to take a look at the roller rockers.|
|07-28-2014 02:15 PM|
Set the lash COLD .004 to .006" less than the cam card hot lash spec.
You can set the valve lash quite a bit tighter and it
Will be quieter at idle.
Like .008" to.010" tighter.
Do not go more than .004" looser.
Most people set the lash too loose.
If the hot lash is.025" hot , try .016" to.018" COLD.
Be sure to use the ic eo method.
Try it. Post your result. Quieter now?
It is a lot more painfree to set the lash cold.
You won't mind doing it.
Set lash once or twice a summer driving season.
|07-28-2014 01:11 PM|
|Dajerseyrat||I just got my solid roller fired up and after a bit of driving about 4 of the valves were way off. mos others were close or within spec. It does sound like something is wrong with the car to an untrained ear...Like a tickity tickity sound..|
|03-28-2008 03:14 PM|
|68NovaSS||I'm running a Lunati solid roller with .590 lift, I pulled the covers twice, a month apart, had one needing adjustment, and it was fat from the start. I ran it on the street all last summer, no adjustments were needed. Just checked getting ready for summer...all good.|
|This thread has more than 15 replies. Click here to review the whole thread.|