Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Misfire
User Name
Password
lost password?   |   register now

Thread: Misfire Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2008 10:21 AM
chevy350_Camd
If its not timeing ...

If your timing shows up good after you pulled the distributor and set it to the number 1 cyclinder check your spark and see if its strong and blue if not it could be the plugs after you rule out the plugs check your coil, And if its misfiring is usually a case of retarded timing and I doubt your 34 degrees before is a little bit to slow Sounds Like a weak spark Good Luck
04-27-2008 09:49 PM
Chevyboy454 That's what I thought but wasn't 100 percent sure. Like I said Big Chevy guy. My thoughts on the newer Ford's are "Well at least they circled the Problem for us". Don't get me wrong I like the older more reliable Fords, (when Ford was built tough) but anything I have to lift the cab off the frame to change a spark plug really iritates me! That's if they managed to stay threaded in long enough to be replaced. However it doesnt matter what you buy today they all have there flaws. I just find in the Tech side of things I see 2 Chevs in my shop to 10 Ford / Dodge / Imports. And the Chev's usually need a Alt / Batt / Brake Job / or an intake,Head gasket job. Particarly the 3.1, 3.4.

Just my 2 cents. lol

Cheers Chevyboy.
04-27-2008 09:41 PM
techinspector1 Yep, Fords number differently. #1 is at the passenger side front, then number straight back on the passenger side 2,3 and 4. #5 is at the driver's side front, then number straight back on the driver's side 6,7 and 8.
04-27-2008 08:21 PM
toecutter I concur with chevyboy454

I would start there so as to be certain of proper mech timing.
04-27-2008 07:55 PM
Chevyboy454 I am a die hard Chevy guy, not too keen on the ford side of things however, If the drivers side valvecover is easy enough, remove it. Pull #1 plug and rotate the crank until the piston is all the way up and the valves are closed. This indicates TDC (Top Dead Centre) Compression stroke. Pull the cap off the Dis and look at the position of the rotor, inside your cap it should be marked with a number one or follow the wire from 1 to the cap. The rotor needs to be pointing to number 1 in the cap so lift it out and adjust acordingly. Not sure what your timing should be set at but if you pulled the Dis you probably put a mark on the base of the dis and the block to indicate where it went, if not borrow a timing light from someone and set her up.

Now I know some fords have odd ball cylinders so you might wanna check for sure what cylinder is number 1, pretty sure its the drivers side closest to the rad, but don't quote me on that. Either way this proceedure will work once you determine number one.

If the valvecover is too hard to take off, TDC is good either you will be bang on or 180 Deg out. If 180 out just pull the dis again and rotate 180.

Cheers and hope this helps. Rick.
04-27-2008 12:16 PM
cdiedrick I did pull the distributor, and I suspected that it might be off a tooth. just wondering which way I should try to move it then
04-27-2008 10:26 AM
Chevyboy454 Sounds like timing for sure, pull off the dis cap and grab a socket and bar, roll the engine until the rotor starts to move then roll it back if you get a delayed movement in you rotor as you turn the crank bolt suspect a bad chain. Did you take the Dis out at any time? Possible you droped her in a tooth off?
04-27-2008 10:25 AM
carsavvycook If the base timing is not set right on most Fords I've seen the idle go up and down, not stay steady.
04-27-2008 10:04 AM
cdiedrick Not sure what you mean by that. It seems to idle fine, its just higher rpms under a load is when the misfire happens.
04-26-2008 05:17 PM
carsavvycook Is your idle searching?
04-26-2008 03:30 PM
cdiedrick
Misfire

I did some work on my engine put in a new oil pump last fall, then winter hit so I didn't drive the car. I was not happy with how it ran but I figured I would get back to it in the spring. It is a 79 T-Bird with a 351M it started hard, backfired and then I got it running. Under a load it misses big time at about 3000 RPM but runs fine otherwise. According to my timing light my timing is advannced 34 degrees. That is a bit much but it is the only way the car runs smooth. What is going on? IS my distributor off a gear perhaps? Did something go bad with my distributor. Any ideas will help.
Thanks
CHris Diedrick

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.