Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Fans not kicking in 'til 237* on a 218* switch
User Name
Password
lost password?   |   register now

Thread: Fans not kicking in 'til 237* on a 218* switch Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2008 05:46 AM
Bryan59EC
Quote:
Originally Posted by carsavvycook
We are assuming it is a SBC any different?
sorry---
454 HO

Close pipe adaptor?
I'll be looking for one this week then.
Have one on my pool----1/8 to 1/4---even if that was the size I needed---I'd have to fight Susan for it---She wants her pool working
04-27-2008 04:35 PM
carsavvycook The fitting you are looking for you can find at a hardware store. It is called a Close Pipe Adapter. It will have no hex and the shortest one will be in cast iron metal. Install it in the cylinder head so it reads right.
04-27-2008 04:03 PM
carsavvycook We are assuming it is a SBC any different?
04-27-2008 04:00 PM
carsavvycook What heads do you have on it?
04-27-2008 03:55 PM
Bryan59EC Nope----
3/8" pipe sender
1/2" pipe intake, heads
04-27-2008 03:26 PM
carsavvycook Put it in the cylinder head, either side you can. The thread size should be the same as your sender. You will find it will work as advertised temp wise.
04-27-2008 02:14 PM
Bryan59EC The fan switch is located in the intake----directly opposite of the temp gage sender.

If the fan switch is working correctly----then the 1,3,5,7 side is running much hotter (15-20*) than the 2,4,6,8 side.

Guess I could swap the sensors around and check for that.
Not gonna do it today tho

not too worried about an overheat at all, runs around 200-205 on the hiway, and that is acceptable to me----(probably could use a bit more timing tho)
04-27-2008 02:05 PM
curtis73 Depending on sensor locations, coolant temps can vary up to 30 degrees throughout different places. Often times there is a 10-15 degree difference between the manifold and the heads.

I wouldn't worry about the shrouding of the sensor. Water is an excellent conductor of heat, plus there is plenty of turbulence around that fitting. Plus, the fitting is probably brass and its almost as good as the water at conducting heat.
04-27-2008 01:20 PM
Bryan59EC
Fans not kicking in 'til 237* on a 218* switch

I'm kinda wondering if anyone here would know where to get a
bushing for a 3/8 switch to a 1/2 intake??

The bushing I am using now shrouds the sensor bulb to the extent that only the bottom of the sensor is exposed to flowing coolant.

Do you suppose this is why the fans do not come on when theya re supposed to?? The first time they are activated by the fan switch, is around 237.
Then the engine will get down to 215 and the fans will shut off. Subsequent cycles will kick the fans on around 228 and off around 210.

This is on a NAPA FS118-----on @218--off@205 switch

Kinda wondering where I could get a bushing that does not have the hex on it. Dakota Digital has bushings for 1/2 to 1/8 and 1/2 to a 1/4 that are only about 3/8" tall. Whear this bushing from Spal (and any others I have been able to find) are close to an inch or better.

Any insight to this?? Is it the bushing shrouding the bulb causing the fans not to come on when they are supposed to??

I have tried 3 different switches (fs118 2x --and a chevy switch once) and get the same results with all of the switches.

This is on the 59 Elky, and temps have been verified by the Dakota Digital gages AND and infared temp meter. (gage and meter match at all temps)

Bryan

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.