Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 390 Fe out of 68 fairlane
User Name
Password
lost password?   |   register now

Thread: 390 Fe out of 68 fairlane Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-08-2008 08:42 PM
j-jock
390 into a 56 truck

One of the things you are going to have to do, is find a truck rear sump and oil pump pickup. The other thing you will need to collect is the oil filter mount from a truck FE engine. These pieces are plentiful, so it is no big deal.
I can't remember whether the front mount points are the same for the Y engine and the FE, I know there were differences in how the mounts attached to the block between the earlier and later FE engines. I believe the mounts will match up to the Y engine mount points. The 68 engine will have the later pattern. I just can't remember but in any case you have lots of room to place the engine properly.
Don't screw up the exhaust manifolds or toss them, If they are original, they are the GT manifold with the staggered bolt pattern instead of the bolt holes at the top and bottom. The headers you buy will have to be for the GT heads. They are excellent heads, so don't exchange them.
I also agree with your decision to use the C-6. It is a great transmission and saves all the headaches of matching bellhousings.
Bob
06-08-2008 07:01 AM
lhthom2
390 fe for 56 f100

The good thing is that when I bought the 390 FE (for $100) I also bought the C6 that was with it (also for $100) and the lady thru in the driveline. I know I will have to have it shortened but I thought by buying both the engine & trans it would save me some hassles as well as the price. She said she needed money fast and I think I got a great deal. Everything is there and it looks like it would start right up right now.

Thanks
LT
p.s. I have another question, I have a chance to buy a Valorie front clip (complete) for $300. I don't know if that is a good deal and my other issue is I am a Ford guy thru and thru and a valorie is not ford. Should I just wait for a good priced mustang II IFS?
06-05-2008 02:55 PM
PatM OldBogie (as always) is right! I can't speak to the various and sundry bolt patterns, but I can speak to the transmissions from 1956. As a kid in high school and college, I went through about 1 a year. And I was never brutal. They just seemed to crumble internally. The manuals, anyway. Dunno personnaly of anyone having trouble with the automatics. But, then again, those engines were only about 200-225 HP. A 390 would give it a lot of extra exercise. Perhaps a C6?

Pat
06-05-2008 02:41 PM
oldbogie
Quote:
Originally Posted by lhthom2
I just bought a 390 FE out of 68 fairlane. I am planning on putting it in a 56 F100. Will this work and if so, how hard?
Thanks
Lynn
The biggest headache your going to hit is Ford's ability to use a half dozen bell housing bolt patterns. If you're planning on using the original 56 transmission, what ever that is, you'll need an adapter between the FE and the existing bell housing. However, the 56 trannies are pretty weak, so coming up with something that originally bolted to an FE would be a great labor and cost savings device at this point.

Bogie
06-05-2008 06:17 AM
Scode68 352 showed up on a lot of blocks so it could be a 352/360/390 but at least itís a 390.

Iíve seen a few 55-57 Tbirds with 427 or 428 engines so I would think the 390 will fit your Pick-Up with no problem. You might have a problem with headers but that should be it.
06-04-2008 01:24 PM
lhthom2
390 Fe

Thank-You very much. I think you answered my question. My block does say 352. I think it will bolt up and that would be a beautiful thing. Thanks again for all of the help. What a great website this has been and I have only been apart of it for about 5 hours.

Thanks again
Lynn Thomas
06-04-2008 01:16 PM
PatM If you post the VIN number here, there may be someone on HotRodders that can help. There may also be a few F100 specific sites out on the internet that will offer more support, perhaps, than this site will. I know that in '56 the only V8 pick-up trucks were all y-blocks. This is the 234(?), 272, 292, 312 series of engines. There were also 6 cylinder trucks. I do not know if the sixes and V8s were readily interchangable, or if engine mount welding was necessary. I do know the first FE motors, the 332 and 352, were introduced in 1958. And I think that the pickups offered both the y-block and the FE for several years. I had high-school friends who put FE motors into '56 sedans, and they worked great. They bolted right in where the y-block used to go.

Pat
06-04-2008 12:01 PM
lhthom2
390 Fe

Thank-You that makes me feel alot better. You brought up another question. Since the truck did not have a motor or trans how do I tell if 292 or 312?

LT
06-04-2008 09:23 AM
PatM I haven't ever done one myself, but I seem to recall that this was a real popular swap about 20-25 years ago. The FE engine pretty much bolts in wherever a y-block used to be, and so if your truck is a 292 or 312, I think about the only thing that'll require change is the throttle linkage. Boy -- That's a memory cell test.

Pat
06-04-2008 08:49 AM
lhthom2
390 Fe out of 68 fairlane

I just bought a 390 FE out of 68 fairlane. I am planning on putting it in a 56 F100. Will this work and if so, how hard?
Thanks
Lynn

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:00 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.