Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> To drill or not to drill steam hole in 400
User Name
Password
lost password?   |   register now

Thread: To drill or not to drill steam hole in 400 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-27-2008 12:44 AM
C-10
Quote:
Originally Posted by techinspector1
See the link I provided in post 3.
10 degrees.. ah. on the intake side. check.

Now I'm going to have to dig up that paper from World products to see if it say 10 degrees also. (It's been awhile)
06-27-2008 12:39 AM
techinspector1
Quote:
Originally Posted by C-10
I think 3 of the 6 holes drilled in each head are at a 45 degree angle. Not sure which ones, Intake or exhaust side. This was stated in my Sportsman II nomenclature.

I'd drill 'em for a siamese cylinder type block.
See the link I provided in post 3.
06-27-2008 12:33 AM
C-10 I think 3 of the 6 holes drilled in each head are at a 45 degree angle. Not sure which ones, Intake or exhaust side. This was stated in my Sportsman II nomenclature.

I'd drill 'em for a siamese cylinder type block.
06-26-2008 08:38 PM
n-gin I called a machine shop a week ago and they told me not to drill the holes and to plug the block I will Not be getting my block done there Gelner

Drill the steam holes its cheap insurance I say
06-26-2008 08:11 PM
j.d.brown.042964 Unless you're gonna do ONLY dragracing w/ engine rpm's primarily over 3000 rpm, all the tech. sources I've ever heard from say to do 'em. My last builder chose not to do them, but I had them added because it's cheap insurance for a "street-driven" setup that will spend alot of time under 3000 rpm. I checked with my head supplier,and because I live close by their Main office-they said bring 'em in and we'll drill them for free, which they did! I agree with what the head designers/supplier say.
Remember of course to choose headgaskets that have the steamholes, as some do not. Fel pro 1014 and 8634 do have them, 1004 and 1034 do not. -Jim.
06-26-2008 07:46 PM
MI2600 For $30 at the machine shop, drilling seems to be a no-brainer. The GM engineers must have a reason for the holes.
06-26-2008 03:52 PM
dawg overall the coolant shouldnt overheat BUT the section that we are talking about will.
you wont notice it until you have a problem.
since you got the heads off its cheap insurance that you wont have a major issue later on.
BTW make sure your head gaskets have the steam hole aswell.
06-26-2008 03:46 PM
techinspector1 The other likely outcome is hot spots that will contribute to detonation.

http://www.gregsengine.com/350to400.htm
06-26-2008 03:43 PM
oldbogie
Quote:
Originally Posted by Curtis Thornton
I am getting different feed back from folks about whether of not I should drill the steam holes in the new heads I just purchased. I bought a set if heads from Jegs (world sportsman). I have spoke to a friend of mine whom has built several small block chevy 400 and he stated that he has never drilled the steam holes out on his 400's and it they have never ran hot.

Are there any pros out there on sb chevy 400 that can give me some insight before I put this thing together
They don't run hot where you can see it, that is the engine temp doesn't increase where the temp gauge sender is.

What happens without the 400 drill is that coolant can't escape from the top of the closed area where the siamesed cylinder bores meet the deck. This coolant turns to steam which is a poor conductor of heat. The local area at the top of the bore overheats and distorts. The likely outcome is cylinder wall and deck cracking in this area, especially around the normally hot running center cylinders on each side and or head gasket failure in this zone.

Bogie
06-26-2008 03:19 PM
Curtis Thornton
To drill or not to drill steam hole in 400

I am getting different feed back from folks about whether of not I should drill the steam holes in the new heads I just purchased. I bought a set if heads from Jegs (world sportsman). I have spoke to a friend of mine whom has built several small block chevy 400 and he stated that he has never drilled the steam holes out on his 400's and it they have never ran hot.

Are there any pros out there on sb chevy 400 that can give me some insight before I put this thing together

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.