Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Do I need to turn or polish my crank?
User Name
Password
lost password?   |   register now

Thread: Do I need to turn or polish my crank? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-24-2014 10:38 PM
markhansenconquest
thanks to all who replyed ....

has anyone tried a ruby stone or a arkanasaw stone to micro polish minor imperfections too small for your finger nail to catch and my crank is nitrited on mains and journals I like the paper bag thing and the leather belt thing. I found out about this site from a friend that I met in a post. those stones are used by mold makers and tool makers to polish mold parts. Im a tool maker 32 years trying to do things by my self if I can . thanks again for all who take time to talk to me and share there knowledge.........
07-23-2008 04:01 AM
techinspector1
Quote:
Originally Posted by DaSouthWon
whats an ok bearing clearance on a ford small block?
For a street motor.....
0.001"/0.002" on the rods, shoot for 0.0015"
0.0015"/0.0025" on the mains, shoot for 0.002"
07-22-2008 11:41 PM
DaSouthWon Ok, I looked in the knowledge base and have done a good bit of searching looking for wear specs, or tolerances on a sbf and I cant really find much. I can find the original part specs, but can't find anything that says what wear is within normal specs and what is excessive and must be replaced. Can anyone guide me in the right direction?
07-22-2008 08:04 AM
red65mustang Da south,
do check out the Knowledge Base link at the top of the page for any motor's specs....
ex:
http://www.hotrodders.com/kb/ford-engine-tech
07-22-2008 07:01 AM
SSedan64 An old leather belt works great for polishing too.
07-22-2008 06:52 AM
lanierledford
polishing a crank

If it mic's OK, I polish my with large brown paper grocerey bag strips (if you can find a brown paper bag now days. Just cut it into strips narrower than the throes of the crank. I have remover-ed small rust spots that aren't bad with it.
07-21-2008 09:20 PM
DaSouthWon whats an ok bearing clearance on a ford small block?
07-21-2008 09:13 PM
Stroke
Quote:
How do I know when I can get away with just polishing the crank and when do I need to turn the crank?
Quote:
mic the crank
Couldn't be said better.
ALWAYS MEASURE!
ALWAYS CHECK - EVERYTHING.
07-21-2008 08:43 PM
sam-missle mic the crank, if it mics good, clean and polish, mic again. small scatches won't cause any problems.

sam-missle
07-21-2008 08:29 PM
DaSouthWon
Do I need to turn or polish my crank?

A friend of mine just gave me the rotating assembly out of a ford racing crate motor he purchased and turned into a 331. He put about 15k miles on the original assembly before pulling it out. After going over the crank most of the journals are still smooth but a few have some small scratches from wear. None of the scratches are really large enough to catch a thumbnail in but their not perfectly smooth either. How do I know when I can get away with just polishing the crank and when do I need to turn the crank? I will obviously replace the bearings, but I would like to get away with not having the crank turned if possible.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:10 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.