|
|
|
03-14-2012, 08:13 PM
|
||||||
|
||||||
|
now that looks darn nice
|
|
03-16-2012, 02:43 PM
|
||||||
|
||||||
|
Holy crap is that well detailed, my favorite thing on a car, detail, shows passion, I dig it.
I have been side railed a bit on my Gran Sport with a project for my wife. I went over to her mom's house to do some work getting a room ready to paint, needs a bunch of work, that's for sure.  Brian
|
|
03-17-2012, 03:31 PM
|
||||||
|
||||||
|
I built and painted a bed for my 47 international. now I have to find or make fenders. all in a days work.
|
|
03-17-2012, 04:50 PM
|
||||||
|
||||||
|
After fighting with the power co. and local inspectors (nobody got hurt) we finally got the power turned on again (a power pole went through our shop roof) so I've been playing catch up for two weeks,I finally got some free time to mess around with the biz coupe again,I made another wheel arch for the rear fender (now I have a pair) I wanted to fire it up and pull it outside but gas started spewing out of the vent hole in the carb ,I guess it sat to long without being run and the float is gummed up,so I pulled the carb off and I'm rebuilding it...One step forward but only one step back today,a good day fer sure...
|
|
03-17-2012, 05:08 PM
|
||||||
|
||||||
|
Good to hear you got back on it!
I got the seats out of the Gran Sport to put the carpet in, but of course I can't stop there and I cleaned up the floor and rust and shot some picklex on there before I paint the floor tomorrow. I also got over to the M-I-L's house and got some work done on painting the bedroom. I still will get out there for some more today but damn it was nice sitting on the couch and watching a ball game too! Brian
|
|
03-17-2012, 05:53 PM
|
||||||
|
||||||
|
Quote:
|
|
03-17-2012, 08:21 PM
|
||||||
|
||||||
|
modified my new lifting table (made its deck bigger) so I could use it to assemble tiller, and then lower to the floor when done
more painting, switching, and assembling rototiller parts should have one whole tiller tomorrow 
|
|
03-18-2012, 03:53 AM
|
||||||
|
||||||
|
I got a set of bead roller dies made for the belt line of my hood.
Too bad they don't work.... 
|
|
03-18-2012, 07:11 AM
|
||||||
|
||||||
|
nissan
Quote:
|
|
03-18-2012, 07:30 AM
|
||||||
|
||||||
|
Quote:
Then you can 'tiller' "I got one ready for ya hon' !" 
|
|
03-18-2012, 07:42 AM
|
||||||
|
||||||
|
Quote:
Brian
|
|
03-18-2012, 08:21 AM
|
||||||
|
||||||
|
Quote:
|
|
03-18-2012, 08:48 AM
|
||||||
|
||||||
|
Quote:
|
|
03-18-2012, 08:55 AM
|
|||||
|
|||||
|
Quote:
|
|
03-18-2012, 11:13 AM
|
||||||
|
||||||
|
Got the bead roller dies tweaked up. Lucky I didn't need to make new ones. I kept shaving them smaller and smaller til I got pretty close.
Should be close enough to visually not see a difference between the lines on the body and the new hood sides.
|
|
|
| Tags |
| build thread, projects |
| Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Another engine "tick" diagnosis thread....(long) | ForceFed86 | Engine | 2 | 04-09-2011 03:54 PM |
| Hahaha Remember that "Hemi in a Camaro" thread... | Crazy Mopar Guy | Hotrodding Basics | 6 | 10-18-2008 06:34 PM |
| Increase thread title "preview" time | cboy | Hotrodders Site Suggestions and Help | 16 | 07-03-2008 08:45 PM |
| MuscleCarKid_1991 "Senior Project" thread: Dumped | Jon | Engine | 2 | 03-22-2008 08:01 PM |
| "Trial fitting parts" thread vs. paint thickness | rcurrier44 | Body - Exterior | 3 | 01-26-2005 05:24 PM |
