Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans Advertise
hotrodders.com: Project Journals: tuske427's Journal
User Name
Password
lost password?   |   register now

View tuske427's profile Entries: 407
Views: 115659
view from the beginning || now viewing most recent entries


Pages (82): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 [81] 82

04-11-2005 09:14 AM Part 7: at the paint shop part 1
Things are moving along slowly, as in anyone's project who doens't have the financial support of wall street behind it. A few weeks ago we dropped the car off at the paint shop (Grangers, Reseda, CA) that will handle this project. Although there were afew cars ahead, it's finally starting to have some attention. Attached are a couple of pics as they made the first pass at stripping the car. Fortunately, there were not too many bad "suprises" underneath the paint. I did learn that both my fenders have been patched at the top above the headlight areas. During this time I am trying to order up as many parts as I can for when it's time to reassemble it. Of course, there will be many things I didn't get and will have to then buy at that time. The last image is a photoshop image I made of what I'd like the car to approximately look like.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #7]

12-28-2004 05:38 PM Plymouth Belvedere part 6
Well these past few months have been slow. Busy with work travelling, family visits, holidays ,etc. . Happens to all of us. Now I can get back to the Belvedere again. This past wekeend I finally received my leaf spring parts form Eaton Detroit springs. It took way longer than expected to get my parts (3 months!) but all's well that ends well. I dissassembled the springs and stripped the rust off. I then painted them and applied a coat of rubberized undercoating. They are currently drying before I re-assemble them. I have also ordered the shocks and received the electric fuel pump to supply the LS1 with "go juice." My next move is to install this while the rear end assembly is out.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #6]

09-23-2004 09:48 AM Plymouth Belvedere part 5
It's September and I have smoothed the welds by covering them in bondo, as well as the firewall pinch welds along the outside. I have also removed some of the loose undercoating to expose any would be rust issues. Fortunately this car is really solid. I didn't have any holes! I understand these cars liked to rust out so I am considering myself very lucky. (I've looked at some other folks who are restoring these cars and they are replacing frame sections, quarter panels, etc.. I had to sand a little) I treated the rust with Eastwood's rust encapsulating paint and reapplied undercoating underneath, in the trunk and on the floor inside. This week I installed the front suspension again and unfortunately, that'll be it for a month and a half while I am travelling for work. I have to prepare and set up our display for the New York Toy Fair in October, squeeze in a trip to Hawaii, then go to the SEMA show and then back to Vegas the following weekend for a bachelor party. Don't get me wrong- I'm not complaining, but it means I have to set aside the car for a bit.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #5]

09-08-2004 01:18 PM Plymouth Belvedere part 4
We got the car back at the end of August. It's looking nice. Since its return I have dismantled everything that was assembled, and started to clean it up. I've used some "bondo" to smooth out the old and new frame sections, as well as clean up the fire wall a little. My wife couldn't understand my efforts in cleaning up the firewall. she just wants it done... I'm a (toy) designer for a living so attention to all the little details are critical for me. Though I will make compromises because this will be a driver and not a 100K trailer queen, I think the engine bay should at least look nice, especially when it's this far apart and considering everything else done so far...

I have also stripped the frame and will apply the Eastwood Company's brand of rust sealing paint. Fortunately for me, this car is not rusted out. I am very lucky to have a clean car to work with. Stay tuned!




(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #4]

08-05-2004 02:27 PM 1957 Plymouth Belvedere part 3
Since I have no competant welding skills we decided to trust the welding/ fabrication to a professional. We chose Todd Walton at Walton Fabrication (Upland, CA) to handle the work. We're glad we did. They have some exceptional skills, and have been very reasonable the entire way through. I highly reccomend these guys if you ever need this type of work done.

as you can see they cut off the original frame rails and fabricated new ones to accept a Ford II style front end. They have also located the engine and made engine mounts for it, too. They have made a trans crossmember and are completing the steering with a column from Ididit. Following this I will take it home to handle the rest of the restoration/ hot rodding.




(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #3]

Pages (82): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 [81] 82


All times are GMT -6. The time now is 01:43 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.