Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans Advertise
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Compressor Water Problem
User Name
lost password?   |   register now

Thread: Compressor Water Problem Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-26-2004 06:54 PM
poncho62 You are getting water from the warm air that you are pumping from the basement to the cold garage. Air gives off condensation when it cools. better to have the compresser in the cold, then there is no temperature change.
12-26-2004 06:49 PM
daimon1054 If water is getting though the filter (you need it as close to the end as said) but if the water is passing you need a larger seperator and a smaller micron filter.
12-26-2004 05:47 PM
air line water

You could do what i did when i had the same thing at a bodyshop that i owned. I took and old drive shaft[the bigger the better]put a petcock on one end for a drain. Then ran my air line in at the center of shaft. Next i took my air off a fitting that i'd put at the top of shaft.Worked great no more water in my paint jobs. I still used a water fillter after my home made water tap. The idea is water is heavyer than air. So when it enters open space in drive shaft it'll fall to bottom of shaft and clean air goes to top of shaft.After a hot summer day you would'nt believe how much water would come out of that drive shaft.
11-26-2004 09:17 AM
Chopper64 If I shot myself in the foot every time I made a mistake I would be wearing a size 3 shoe instead of my 13s.
11-26-2004 09:03 AM
MI2600 Thanks Chopper.

Some good tips. Thankfully, my piping only runs about 20 ft, but I can see where I shot myself in the foot.
11-25-2004 09:08 PM
Chopper64 It's a good idea to make that pipe coming out of garage as high as possible then drop down to your outlets. Slope the pipe downward to the flow of air.

This link is a beauty for garage piping.
11-25-2004 09:01 PM
MI2600 Thanks Bob. I can do some redo of the pipe in the garage for another filter. I think it'll be ok to leave the other one in.
11-25-2004 12:12 PM
[email protected] Your filter/oiler should be as close to the hose as possible. Otherwise the water vapor in the line condenses between the filter and your outlet, before it gets to your hose.
11-25-2004 11:54 AM
Compressor Water Problem

I've got a Craftsman 30 gallon compressor that I put in the basement to lessen floor space problems in the garage.

I ran pipe up to the garage and installed an in-line water filter and an oiler in the basement. On the end of the pipe, I have a 30 ft hose that I have never removed. I empty the compressor tank after use.

The problem I have is a lot of water in the line. The water filter gets a light mist inside it, but doesn't seem to trap much.

Should the filter be closer to the end of the pipe?

Any suggestions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:21 AM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.