Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans Advertise
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Suspect front brakes doing all the work?
User Name
lost password?   |   register now

Thread: Suspect front brakes doing all the work? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-02-2018 02:44 PM
db flyer Interesting update on my brake situation. I did check out the link you sent on proportional valve adjustment, and turned valve in both directions to each stop,
and made no difference at all. Appears as though the valve does not work at all, even though it did when I installed it 5 years ago. I put my brake pedal down with a bar resting against seat and confirmed rear brakes were locked also made sure fluid was present at master cyl. to rear brakes and at P. valve.
Also raised rear or car and ran engine in drive and confirmed wheels stopped as I applied brakes. Went out for a road trip and tested stopping at many stop signs with no rear brakes grabbing seamed fairly normal. Seems like P. valve
does not work which seems strange that rear brakes are not grabbing no matter the valve adjustment ?
07-30-2018 07:03 PM
68NovaSS Here's a page from SSBC's installation manual regarding adjustment.
07-30-2018 02:21 PM
db flyer Thanks for that brake/gravel test of proportioning valve. I had wondered if the valve may be adjusted wrong, as I had trouble with rears locking up and just tweaked the valve until rears did not lock up, but maybe went too far with the knob. I assume turning the valve clockwise decreases fluid to rear?
07-30-2018 02:01 PM
OneMoreTime A good test is to take the car onto a gravel parking lot and dynamite the brakes at a low speed. The lockup marks left in the gravel should be about the same length if the brakes are working evenly. Then out on the road course you can do this at some higher speed to see if your adjustment of the proportioning valve is close to correct. Having a higher pedal upon replacing a master cylinder is normal to me as the new cylinder is acting a bit quicker than the old worn one.

07-30-2018 12:16 PM
db flyer Thanks for the reply. my 56 chevy is not power brakes, and I do have a proportioning valve, and rear shoes are new and are adjusted properly.
Do you think adjusting the piston pedal rod so that the brake pedal will
go lower to floor will go deeper in cylinder and maybe help?
07-30-2018 12:04 PM
68NovaSS Are your rear shoes adjusted properly? I assume you have a proportioning valve in the system, otherwise your rears would be locking up early. Isa this a power brake system?

If this is a large bore GM master cylinder, they have a different depth rod 'seat' in the rear, do you have the correct length for your MC?
07-30-2018 09:43 AM
db flyer
Suspect front brakes doing all the work?

I just installed a new master cyl. with a bigger 1-1/8" piston, which also required a different pedal rod setup and adjustment. I have disc on front and drums on rear. Both front and rear are new within 300 miles. I have a higher pedal for braking now but not any difference in stopping power. However when I come to a slow stop I get what I call a groaning noise that sounds from the front as I put more pressure on brakes. Could this be a rod adjustment to the pedal? Thanks for any help. Duane

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 09:59 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.