Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans Advertise
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Fiberglass pain stripping
User Name
Password
lost password?   |   register now

Thread: Fiberglass pain stripping Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-14-2018 06:11 PM
chphlds thanks for the info. sounds good .appreciate it.
11-13-2018 07:26 AM
shine the paint is old lacquer checking. the stars are rock chips in the glass itself .
using a razor blade and heat gun on low is the best route to take. it takes a little practice but goes fast once you get the hang of it. use a razor blade holder. rub the blade backward on your jeans or the surface to curl the edge slightly . take small 1/4 strips at first.
10-26-2018 03:51 PM
idrivejunk Oh my goodness, I have not dealt with anything that bad. A filler and paint redo in modern products could buy quite a bit of time. But it looks to me like the fiberglass is showing its age. I can't be much help though, and maybe its not as bad as I think. I hope not.
10-26-2018 11:10 AM
chphlds
paint checking on fiberglass

hey guys,here are some pics. of paint checking on my 34 fiberglass.the car was built in 86 and this is the original paint,so it is probably laquer.looks like it wood come off easiAttachment 437043

Attachment 437045

Attachment 437047

Attachment 437049

Attachment 437051ly.any sugestions would be greatly appreciated.
10-23-2018 04:43 PM
chphlds
34 checked paint

thanks for the info.i was given two diferent prices to strip and repaint. one was 8000 the other 6000. both over my budget,so i am doing it myself[just the stripping]the guy for 6000 said he would use razor blades to strip.doyou think that is what i should use?this is my first atempt ,so once again any help is appreciated.will sends pics.of what i am up against tomorrow. thanks
10-21-2018 06:46 PM
MARTINSR
Quote:
Originally Posted by chphlds View Post
hey guys,
my 34 ford fiberglass paint is checking.from what i have herd the only way around this is stripping the paint.any ideas would be much appreciated. thank you
Post a few photos so we can see where this is happening. A few close up, then a few a ways away so we can see WHERE it is on the body.

Brian
10-21-2018 04:24 PM
idrivejunk You heard right. Beyond that, you have to take away the cracked material even if the problem's root is in the fiberglass itself. In order to determine a proper course of action, you'll remove material until cracks are gone. On the 'glass itself, cleaning with wax and grease remover after sanding away all visible cracks and blowing dust out with compressed air helps to reveal more cracks because the solvent wiil be wet inside them after the solvent on the surface dries. It can be tough to find them all.

Once you determine the extent of the issue, post pictures if you can. My fiberglass experience is fairly basic but others here with more advanced knowledge can be more specific if you show the problem.

Expect the cracks to be the tip of an iceberg, thats usually the case. If it turns out to be just paint thats cracked, consider yourself fortunate. Theres not a shortcut that lasts many years before the issue reappears, if the fiberglass is the root cause. Fiberglass is, by nature, imperfect. Cracks may or may not represent defective manufacturing, and some cracks are pretty much expected eventually in any of it.
10-21-2018 03:51 PM
chphlds
Fiberglass pain stripping

hey guys,
my 34 ford fiberglass paint is checking.from what i have herd the only way around this is stripping the paint.any ideas would be much appreciated. thank you

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:18 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.