Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans Advertise
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> AN Fitting to Aluminum Tube
User Name
lost password?   |   register now

Thread: AN Fitting to Aluminum Tube Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-28-2019 01:59 AM
MoonBat I decided to go with flare fittings. Got the tool today and made a couple flares for practice.
Part of this project is to have a fun ride when I'm done ('31 Model A roadster hot rod). The second is to learn new skills.
Thanks for the helpful posts.

Buzz (MoonBat)
03-13-2019 06:10 PM
cerial So were looking at this:'s/361/AT...xoCrjwQAvD_BwE

Which I hate and can see leaking with high pressure once any coating around that tube gives way or the aluminum does not get crushed perfectly by that sleeve.

Why not get rid of the tube completly with a bulk head fitting?

Drill out the tube and run a an-8 bulkhead fitting.

Pull the sending unit/ pump cover. Run the pump to submersible fuel hose to an-6 male barb /an8 female(reducer below link) to an8 through connection(above link)(that is a 10 use a 8 of course) to an8 female to barb or female swivel for the rest.
03-13-2019 03:14 PM
dusterdude3404 If you're using a low pressure pump for a carburator,the compression fitting will do just fine.if efi,i would flare it.

Sent from my LG-US601 using Tapatalk
03-13-2019 03:13 PM
ericnova72 IMO its a matter of having the correct tools.... a lot of guys don't do enough AN line flaring to recover the expense of the 37 flaring tool.

Don't forget that the flared aluminum line also needs a tube sleeve to go along with that tube nut.

I have used the compression fitting type hard line to AN adapters several times without a problem. Compression fitting on one end and AN male on the other was the type I can get them with AN female also.
I don't remember if they were Earls or Russell.
03-13-2019 01:01 PM
AN Fitting to Aluminum Tube

I am running a fuel line from a trunk-mounted fuel cell. The fuel line is 3/8" OD annealed aluminum and the fitting at the fuel cell is AN-8. The tube manufacturer (Earl's) says the tube can be flared. I have ordered a AN-8 to AN-6 reducer to match the tube size
I am inclined to use a flared fitting rather than a compression fitting but I would appreciate input from more experienced rodders. Is one type superior or is it a matter of available tools ?
Buzz (MoonBat)

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 12:04 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.