Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans Advertise
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Oil Separator/Vacuum Pump Issue
User Name
Password
lost password?   |   register now

Thread: Oil Separator/Vacuum Pump Issue Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-15-2019 06:59 AM
predator carb guru I run a Moroso separator and a Star pump. It's got the same foam baffling you mention but the shape of the can at the top prevents it from being pulled out of position. I also take some brake clean on the inlet to the vacuum pump every so often to clean it. It does help.
06-13-2019 11:26 AM
chasracer
Quote:
Originally Posted by johnsongrass1 View Post
A whiffle ball will hold the foam down if it happens again.

Excellent idea!! Thank you!
06-13-2019 07:47 AM
johnsongrass1 A whiffle ball will hold the foam down if it happens again.
06-13-2019 06:39 AM
chasracer
Oil Separator/Vacuum Pump Issue

Ran into an issue at the track last time out. Out of the blue, I had a zero vacuum reading on the gauge and best I can figure after cleaning up everything is that oil sprayed out from the keyway in the dampener.



My vacuum setup is a Star Sportsman pump, Stef's Oil Separator and a Moroso catch can. I pull from the end of the valve cover over to the oil separator which feeds the pump and then any residual goes over to the catch can. Pretty tight setup as I only use a piece of flex hose between the pump and catch can, everything else is braided stainless and AN fittings. Most of the time flex line and push locks are used for all the lines, but I don't like that setup.


I warmed up the engine yesterday and tried all the tricks I had to find where it was losing vacuum at. The engine idled just fine so my thinking was I had either a valve cover or oil pan seal sucking air. I couldn't find a thing, but I took the connection off of the valve cover and verified that I had vacuum being pulled by the pump however I thought that it was weaker than what I expected. I verified that the gauge line connection was good too. I shut it down and was totally mystified. Finally, I figured I would drain the catch can and oil separator tanks. Just about zero oil/water out of either of them - a few drops which was really strange. Normally I can get a good sized dixie cup filled from either one after just a few passes. Finally I removed the top on the oil separator and there it was - the can is loaded with multiple layers of dense foam rubber - similar to the closed cell stuff used to stuff windows for cold drafts. The top piece had been pulled upward in the can and sucked over into the main center tube of the can - this feeds the vacuum pump. I got all of this straighten out, fired the engine and within a minute had my normal 6" of vacuum at idle.



Hopefully this was just a one time thing. But it also proves that no matter what problem we run into working on our rides - there is always an answer. Finding it can be a long road, sometimes expensive but you have to keep questioning what is happening and pay attention to the clues that you are given.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:00 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.