Hot Rod Forum banner
Cancel

Media added by mikesnyhere

Navigation

  1. Member Galleries 45K
  2. Photo Journal 86K
  3. Hot Rod Shows 2K
    1. USA 1K
      1. Rhinebeck Show and Swap 35
      2. Bonny Eagle Car Show 45
      3. Fresno Autorama 42
      4. Maumee Super Street Car and Truck Show 11
      5. Tucson Chevy Show 14
      6. Mid-America Street Rod Nationals 14
      7. Portland Roadster Show 14
      8. Riverside Park Machines 19th Annual Car Show 6
      9. Boise Roadster Show 4
      10. Southwest Street Rod Nationals 7
      11. Gates Rubber Company Annual Car Show 25
      12. Syracuse Nationals 28
      13. Eureka Springs 2003 Car Show 28
      14. Bearing Burners 4th Annual Cruz-In 21
      15. Branson Missouri Cruise and Show 29
      16. NSRA Nationals East 8
      17. National Night Out 17
      18. Downeast Street Rod Run 12
      19. Goodguys 11th Lonestar Nationals 155
      20. Goodguys 13th Heartland Nationals 21
      21. Tontitown Rod Run 85
      22. Goodguys 17th Pacific Northwest Nationals 7
      23. Branson Super Cruise 157
      24. Port Orchard Car Show 72
      25. Farmington Arkansas 2005 Show 37
      26. Branson Missouri Super Summer Cruise 76
    2. Canada 41
    3. Australia 68
      1. Canberra Rod and Kustom Krooze 49
    4. UK 8
    5. Africa 429
      1. South Africa Nationals 2003 163
      2. Cars in the Park 2003 92
      3. Cars in the Park 2004 131
      4. South Africa Nationals 2005 43
Browse albums
heres the kreg jig worth the 100 bucks once you get the setup rite for your material its easy .

heres the kreg jig worth the 100 bucks once you get the setup rite for your material its easy .

  • 0
  • 0
57 truck project is put on hold now to get the garage shop in shape

57 truck project is put on hold now to get the garage shop in shape

  • 0
  • 0
too many projects to be without a proper shop . the Honda engine blew up , and is completely disassembled . my girlfriends bike she also tore it down

too many projects to be without a proper shop . the Honda engine blew up , and is completely disassembled . my girlfriends bike she also tore it down

  • 0
  • 0
shed , most siding on door functions

shed , most siding on door functions

  • 0
  • 0
shed , garage cabinets , couple of carcass done .

shed , garage cabinets , couple of carcass done .

  • 0
  • 0
shed , garage cabinets , cherry tree 006

shed , garage cabinets , cherry tree 006

  • 0
  • 0
bought a kreg jig and some 19/32 plywood , had it cut to 1' x 4.

bought a kreg jig and some 19/32 plywood , had it cut to 1' x 4.

  • 0
  • 0
garage cabinets

garage cabinets

  • 0
  • 0
garage, in need of cabinets

garage, in need of cabinets

  • 0
  • 0
door panel repair 027

door panel repair 027

  • 0
  • 0
door panel repair 028

door panel repair 028

  • 0
  • 0
the pinch hasn't been beat down all the way yet I want to put in some seem sealer then finish it before it dries .

the pinch hasn't been beat down all the way yet I want to put in some seem sealer then finish it before it dries .

  • 0
  • 0
the small spot is a f^%$# up not too bad for a first attempt . still need to be beat on some .

the small spot is a f^%$# up not too bad for a first attempt . still need to be beat on some .

  • 0
  • 0
of course the hindge side that's barely seen turned out way better ! still needs finished .

of course the hindge side that's barely seen turned out way better ! still needs finished .

  • 0
  • 0
this is where it didn't match up to the original very well . getting close but ran out of gas !

this is where it didn't match up to the original very well . getting close but ran out of gas !

  • 0
  • 0
ok so I butt welded both inside and outside , but I think I need to learn to make a flange . I will be watching more vids to figure it out .

ok so I butt welded both inside and outside , but I think I need to learn to make a flange . I will be watching more vids to figure it out .

  • 0
  • 0
door panel repair 021

door panel repair 021

  • 0
  • 0
I have a whole new understanding about repop panels fitting and lining up issues , lots of little cuts and welds to make this better .

I have a whole new understanding about repop panels fitting and lining up issues , lots of little cuts and welds to make this better .

  • 0
  • 0
first time ive ever done this kind of repair . next time I would not replace so much of this panel the rust didn't come up this far .

first time ive ever done this kind of repair . next time I would not replace so much of this panel the rust didn't come up this far .

  • 0
  • 0
came out good .

came out good .

  • 0
  • 0
when the measurement was right I tacked in 2 places and used the edge of new panel as a guide for cutting disc. some people scribe it then cut it free

when the measurement was right I tacked in 2 places and used the edge of new panel as a guide for cutting disc. some people scribe it then cut it free

  • 0
  • 0
door panel repair 012

door panel repair 012

  • 0
  • 0
I watched some youtube vids for instruction . take measurements for future reference .

I watched some youtube vids for instruction . take measurements for future reference .

  • 0
  • 0
take a measurement from BOTTOM of door before anything mine was 12" whatever you decide make sure its the same length before the new panel gets w

take a measurement from BOTTOM of door before anything mine was 12" whatever you decide make sure its the same length before the new panel gets w

  • 0
  • 0
take measurements before grinding the edge ! I used a chisel to break the spotwelds most of them popped apart with little effort . 2 spot welds needed

take measurements before grinding the edge ! I used a chisel to break the spotwelds most of them popped apart with little effort . 2 spot welds needed

  • 0
  • 0
Top