Search Results for ‘mustang’

Hello, I had a question, this is my first project and just wanted some input and advice! Please and thank you. I was just curious on what else I would need prior to starting and or what else I should grab. I have a Th350, aluminum driveshaft, fuel lines, some sbc mounts, anything else that’s...

I just built a 306 and had it dynoed, it made 701 at the crank. How much horsepower is it at the wheels? Is it the 15 percent rule? Thank you in advance Sorry

Hello, I’m new here seems like an awesome page. I have a 92 lx with 331 stroker, GT40 polished and forged heads, BBK headers, mech roller cams demon 650 carb, roller rocker arms, PA racing trans super competition(1,000 HP), C4 tranny, stall is 3,000 CFN for NOS. Headers, runs on pump gas, much...

So I've been planning on buying a 1980s Foxbody mustang and have an engine lined up that I wanted to swap into it. I bought a 1990 F-250 Lariat that came with a Ford 460 and I was hoping to pull the engine and drop it in a Stang but now I'm being told it's a bad idea and that it won't handle the...

Does anyone know what year Mustang spindles and disc brakes will bolt up on a '67 Fairlane?

I'm replacing this switch and harness on a '67 Fairlane. The Ford part number for this car and a '67 Mustang are the same and I ordered a Mustang harness. However, when I got the new harness it has an extra wire in the harness that's red. Fairlane has nine wires the Mustang ten. The Ford...

I'm looking to convert my 1966 Mustang to a rack and pinion set up. Just doing some quick research there seems like there are a lot of different conversion kits out there. Does anyone have any insight on which one is the best? Also my mustang has a manual transmission with the factory clutch...

Hey there, just opened a hotrod shop in eastern Washington! working on a 72' stang convertible right now. Will post pictures!

I need more help guys. I have a 1994 Ford Mustang GT, w/ HO 5.0l engine. The engine was recently replaced with the ford racing engine, GT-40 aluminum SVO "X" heads, X-303 cam, Cold air intake. Ran my engine codes today, came back w/ lean condition on right and left sides, and the EGR vavle...

Names Mike, i'm new here. I am in the process of restoring a '65 mustang coupe. When I bought this car i was told i did not have the original motor or trans but I was given the same setup that it originally came with. Previous owner trying to return it to original. Now knowing this I had no...

How much is a reasonable cost for a 2003 Ford Mustang V8 engine, 4.6L, 32 Valve, DOHC? Thank you.

Does anybody know what would happen if I put new axles in without an abs ring? I have a 95 mustang gt and I'm thinking about replacing my old ones for some alloys but I don't want to go through pressing on new rings if I don't need them. I know it won't be as safe but I just need to know if the...

heads are casting #16485906 they are on a 68 chevy 350 bored 50 over what does that make the 350 a 359??? and its in a 93 mustang lx i know i know how could you do that ruin a mustang but this ford is built ford tough with chevy stuff LOL thanks for any help

I have just bought this 1949 F1 fitted with air ride and I am told a mustang front end. I want to rebush it etc but am having bother identifying the year etc. Anybody recognise it? cheers

Hey everybody I want to know If I Can run a simple plate system to my current setup?? I WANT to spray 150-200 shot I have a 350 1 piece 87 2 bolt block std deck height 5.7 rods 20over stock crank 20over.. trw .100 dome piston .30 over.. comp cam flat tappet 252 260 @0.50 10:6 comp Brodix...

I have owned a 65 mustang for four years and just realized that the the data plate is not on the car! i should have checked be fore but now I would like to know what and were the car came from.The original window sticker would be the holy grail.The vin # is 5f07c694905. Any help out there??

Just posted on Yahoo: "Microsoft Mustang: How cars would look if the software giant ran Detroit". Got enough computer? ;)